Roof repair made leak worse and roofer says it looks fine
Applying coating on top of slate or patching straight over a coating traps water and flakes off after a year, causing leaks to get worse. Roofers and project managers often claim the installation has no visible issue or is all good, leaving homeowners stuck with poor drainage and ongoing leaks. Getting a reliable fix then requires going back through contractors or bringing in another roofer to inspect and repair it.
Core Friction Pattern
Analysis of 3 peer accounts across online developer and community forums reveals that “Roof repair made leak worse and roofer says it looks fine” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.
+3 alternative community-tested workarounds cataloged below.
What people tried
Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.
Found another way around this?
Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.
Roof repair made leak worse and roofer says it looks fine
- 1Asking the seller to handle the repair before closing.Did this help you?
- 2Having the roofing company's project manager inspect the work.Did this help you?
- 3Bringing the issue to the attention of the contractor so they can communicate with the rooferDid this help you?
- 4Having the contractor potentially call in another roofer to inspect the workDid this help you?
In their words
Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.
“Since then the leaking is a lot worse and they say there is no visible issue with their installation.”source ↗
“I have the feeling the coating going on top rather than under the slate is backwards.”source ↗
“Well, that’s why I thought it was wrong, just gravity. But the project manager of the company (highly rated) came to have a look, and told me it was all good”source ↗
“I'd appreciate any feedback on this roof repair/scupper installation. It was just done yesterday and I'm not sure it will drain properly. Also surprised they didn't clean the area where the new torch down went. Should I be concerned?”source ↗
“I've had to repair so many of these patches where they adhered straight to the coating and then a year later the coating flakes off and the patch leaks.”source ↗
“I've brought to the attention of my contractor and he is communicating with the roofer. Contractor may call in another roofer to inspect. I'm so sick about this.”source ↗
“Yeah! I thought for 5K the licensed roofer would slope to the scupper and it would look better than if a kid did it on the side.”source ↗
Where this came up
People with this problem also raised
Related community dilemmas clustered by discussion consensus
How to fix cement fiber siding touching roof shingles
Cement fiber siding installed directly against roof shingles without the required one to two inches of clearance or flashing causes rot, water intrusion, and siding deterioration. Cutting away the tight, awkward sections of damaged material to add proper clearance is physically difficult and risks forcing homeowners to completely replace large wall sections if left unaddressed.
Roofers damaged my house during installation
Crews are failing to use protective tarps, resulting in obliterated gardens, unprotected AC units, and heavy debris smashing into surrounding decking boards. On the roof itself, workers are making sloppy, unoverlapped cuts in new flashing and slicing directly into brand new plywood, causing the boards to flex between the rafters. When confronted about this reckless collateral damage, the contractors gaslight homeowners by insisting it is completely normal.
Roofers left mono roof top exposed without a cap
Contractors frequently finish single-slope or mono roofs without installing necessary ridge caps or drip edges, leaving the exposed edges vulnerable to rain and snow. Homeowners are left arguing with general contractors over missing flashings and trying to figure out what specific finishing corrections to demand.
How to fix a leaking skylight after rain
Water leaks around a skylight during a windy rainstorm are typically caused by a compromised seal or flashing at the top of the frame. Inspecting the roof helps identify whether the seal has failed or if additional flashing like a cricket is needed to divert water away from the opening.
Can I do my own roof maintenance and repairs?
Determining whether you can handle roof maintenance independently is difficult when visual checks from the street miss sloppy transition work and open entry points for rodents. Without knowing what specific sealants or fixes like metal headwall flashing to use, homeowners risk missing hidden defects that lead to leaks and attic pests.
Uneven shingles and bulges after new roof replacement
New roof replacements sometimes show bulges or shingles that fail to lay flat, signaling potential issues with installation or underlying deck structure. When contractors leave these irregularities unaddressed, homeowners are left questioning the quality of the work and whether it compromises the roof's integrity.