Said It Here

How to wire an automatic light for double doors?

A single door switch only turns the light on when that specific door opens, leaving the light off when the other door is opened. Wiring two switches so an overhead or recessed light turns on when either door opens and turns off only when both are closed is hard to piece together. Adding switches can also require cutting into the door frame and rough framing.

OverviewLatest thread: Nov 2026
People affected2 accounts (1 forum)
Workarounds found6 items recorded
Discussion timelineNov 2026
Freshness statusActive Consensus
Editorial ConsensusSynthesized across r/askanelectrician · Nov 2026
Verification standards →

Core Friction Pattern

Analysis of 2 peer accounts across online developer and community forums reveals that “How to wire an automatic light for double doors?” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.

Top Peer-Reported Fix
Wiring two momentary push-off switches in parallel so either door completes the circuit

+5 alternative community-tested workarounds cataloged below.

Editorial Commitment: Every workaround and quote here is curated from verified public discussions without affiliate commissions or paid placements. Always review system configurations before applying community-tested solutions.

What people tried

Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.

Found another way around this?

Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.

Active Consensus (Latest: Nov 2026)Indexed across peer discussions from Nov 2026 to Nov 2026
Evaluated against breaking changes & deprecations
  1. 1
    Wiring two momentary push-off switches in parallel so either door completes the circuit
    Did this help you?
  2. 2
    Installing a motion-sensing wall switch or motion-sensing light fixture instead
    Did this help you?
  3. 3
    Using magnetic reed switches with a low-voltage relay and transformer
    Did this help you?
  4. 4
    Installing only one switch on the primary door and accepting the limitation
    Did this help you?
  5. 5
    Using low-voltage purpose-built products like the Betterswitch
    Did this help you?
  6. 6
    using a motion sensor
    Did this help you?
Tried another approach not listed above?+ Share your workaround ↑

In their words

Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.

r/askanelectrician2 people · November 2026

“About a week ago, I posted seeking help wiring two momentary off switches to each of my (2) pantry doors, hoping that I could have the overhead light turn on when either of the doors opened, and off when they were both closed.”source ↗

PlainOldWallace · r/askanelectricianNov 2026· 11 upvotes

“I ordered one of these switches, but realized today that it'll only work when one door is open. So if the switch is on the right door, and I open the left door, the light won't kick on.”source ↗

“Before I order a second switch (if that's my solution,) can someone please instruct me on how to wire one of these on each door, and have the light kick on if only one of the doors is open?”source ↗

PlainOldWallace · r/askanelectricianNov 2026· 5 upvotes

“I did one of these on my pantry and had to hack the fuck out of my door frame and rough framing to do it.”source ↗

jdwhiskey925 · r/askanelectricianNov 2026· 1 upvotes

“it's a recessed light in the ceiling, I'd really just like it to turn on when I open either of the doors, and go out when both are closed”source ↗

PlainOldWallace · r/askanelectricianNov 2026

Where this came up

People with this problem also raised

Related community dilemmas clustered by discussion consensus

6 related topics

Why do motion sensor lights keep turning off at a desk?

Motion-activated lights in workspaces frequently time out, requiring people to flap their arms around every half hour just to keep the lights on. While occupancy sensors are the new standard, their performance is often pretty bad compared to avoiding tedious voice assistant commands.

6 workarounds3 accounts · 1 forum

Why does turning off the light switch turn off the outlet?

When an electrical outlet is wired to a light switch, it loses power completely whenever the switch is turned off. This prevents people from using devices that require constant power, such as shavers, curlers, and toothbrushes.

1 workaround2 accounts · 1 forum

Weatherproof smart switch mounted over an outdoor wiring box

Standard smart switches aren't built for outdoor exposure, while outdoor timers and weatherproof housings may not fit directly over an existing wiring box. That leaves people looking for a replacement that stays weatherproof outdoors and mounts right onto the wiring box.

8 workarounds2 accounts · 1 forum

Can a smart switch control a smart light?

Voice assistants struggle to sequence turning on a smart switch, waiting a few seconds, and then adjusting the smart light's color and intensity. Because finding a single device that solves this is difficult, people stall their projects or compromise between having full smart control and keeping a physical switch that works when the hub is down.

4 workarounds2 accounts · 1 forum

Why does my GFCI trip when wiring lights to it?

Wiring lights onto a GFCI circuit frequently causes unexpected tripping alongside hazardous issues like power on the neutral wire or swapped hot and switch wires. These wiring confusions prevent homeowners from safely finishing junction box connections without triggering electrical faults.

3 workarounds3 accounts · 1 forum

What do red wires mean in a 3-gang switch box?

Finding unexpected red wires instead of white makes it difficult to identify the switch leg versus the hot black wire. This confusion leaves people stuck trying to figure out if adding a new light is a reasonable DIY project or if they should hire an electrician.

13 workarounds7 accounts · 2 forums