Replacing a rusted well pump pressure tank and plumbing
Corroded pump connections and burst internal bladders ruin pressure tanks, forcing homeowners to relocate new tanks or replace them with different sizes. Dealing with these plumbing failures makes it difficult to secure safe, leak-free connections without knowing if alternative tank dimensions will fit the system.
Core Friction Pattern
Analysis of 3 peer accounts across online developer and community forums reveals that “Replacing a rusted well pump pressure tank and plumbing” repeatedly surfaces due to edge-case mismatches between standard defaults and real-world environments. Standard troubleshooting frequently falls short, compelling practitioners to develop custom workarounds.
+4 alternative community-tested workarounds cataloged below.
What the numbers show
Counted from the threads quoted below. How we count
- People have been saying this in most months since September 2026.
What people tried
Every workaround mentioned in the threads below. We haven’t tested any of them — and nobody here is claiming they worked.
Found another way around this?
Share your steps and trade-offs so fellow engineers don't have to reinvent the wheel. No account required.
Replacing a rusted well pump pressure tank and plumbing
- 1leaving the old corroded tank in place to serve as a pump stand while placing the new pressure tank to the sideDid this help you?
- 2using stainless steel nipples instead of PVC for plumbing connectionsDid this help you?
- 3Comparing physical dimensions side-by-side at the shop and relying on seller advice regarding tank expansionDid this help you?
- 4Hire a professional company to do the replacementDid this help you?
- 5Buy parts and tools to do the replacement DIYDid this help you?
In their words
Unedited, grouped by where they were said, most upvoted first within each place, each linked to the thread it came from.
“I am looking for some advice on how to replace the expansion tank, and subsequent gate valve that goes to the expansion tank that is extremely crusty, I touched it and it is now leaking (no shocker really).”source ↗
“Will I need to bleed the system once i install the new tank? The big pipes are all going to the radiators throughout the house, so if I remove the tank gate valve, wouldn't that let all the water out of the system?”source ↗
“Will i need to drain/fill the system to do this? or shut off the valve left of the little bell, remove the old expansion tank and shut off valve, and install new.”source ↗
“These lines leaked at the pump connection, corroding the pressure tank under the pump that served both as a pump scaffold and a pressure tank.”source ↗
“Pressure tank is shot- so I got a new one- which I'm placing to the side of the old tank”source ↗
“Hi guys need advice, the rubber inside our 80L bladder tank has burst and when we went to shop to buy a new one they only have 100L from different brand but we dont know if it has the same dimensions but when we compared it side to side its a little bit the same ours just a bit bigger the seller says because its hursted and already expanded. Should we buy the 100L?”source ↗
Where this came up
People with this problem also raised
Related community dilemmas clustered by discussion consensus
Temporary fix for a snapped coolant expansion tank nipple
Plastic coolant tank nipples often become brittle and snap off due to heating and cooling cycles, leaving no stub to connect the bleed hose to. While waiting for a replacement tank to arrive, temporary fixes like epoxy often fail to adhere to the pressurized plastic, leaving drivers stuck without a reliable way to drive their car.
How to find replacement parts for a rusted water heater vent pipe
Rust on a water heater or boiler exhaust pipe can usually be fixed by replacing just the damaged vent sections rather than the entire appliance. The main difficulty is identifying the correct name and part for the pipe running from the unit up through the roof so you can swap out the rusted components safely.
Why do sewage grinder pumps keep failing?
Sewage grinder pumps are failing repeatedly within a few years because replacement contractors offer no diagnostics, leaving homeowners to face mounting costs and recurring breakdowns. This cycle is compounded by confusion over sump basin design and whether basin walls require custom or standard drainage holes.
How to fix a leaky plumbing valve that doesn't fit a new faucet
Non-standard valve connections often fail to sit flush with new faucet lines, and older diverter stems may require specific replacement washers. Mismatched sizing prevents a proper watertight seal, forcing you to replace incompatible components or track down exact-fit washers.
What replacement material should I use for a corroded pipe nipple?
Corroded galvanized pipe sections and completely seized threaded flanges connected to copper or brass elbows leave zero room to work in tight wall spaces. This makes it difficult to remove the damaged parts and determine the proper replacement material to stop leaks.
How to replace a roof pipe boot with a cap
A pipe cap prevents a normal replacement boot from sliding over the pipe to seal holes leaking into the attic. Because split boots designed to wrap around the pipe are hard to find, homeowners resort to cutting a standard boot, duct taping it, and sealing it with roofing caulking.